The whole wall decoration board is common in our home decoration. Although it is a simple decorative board, the effect after the design is very good. Here we take a look at the construction process of the whole wall decoration board .
Overall wall decoration board construction process
Material requirements:
1. The tree species, specifications, and material grades of the timber shall meet the requirements of the design drawings and the provisions of the “Code for the Construction and Acceptance of Wood Structure Engineeringâ€.
2. The material used for drying aggregates is generally korean dry material, and its moisture content is not more than 12%. The material must not be rot, knotted, split, twisted, and other defects, and it should be pretreated with antiseptic.
3. The lining board is made of 15mm thick fine wood board, and the panel adopts bamboo wire sound-absorbing board.
4. Excipients: Adhesives, preservatives, latex, sodium fluoride (purity should be above 75%, free hydrogen fluoride, its viscosity should pass 120 # sieve); nails: selected length specifications should be the thickness of the panel 2- 2.5 times.
Construction process:
1. Finding position and playing line: Before installing the wooden siding, according to the requirements of the design atlas, the elevation should be found in advance, and the plane position and vertical dimension should be used for elastic line.
2. Check the embedded parts and holes: Check the embedded parts after the line, whether the wooden block or the wooden wedge meets the design requirements, and arrange whether the spacing size and position meet the requirement of the mounting keel; measure the position and size of the doors, windows and openings; And whether it meets the design requirements.
3, shop, painted moisture layer: design with moisture requirements when the wood wall, wood keel installation must find the right, find the straight, the gap between the skeleton and the wood should be padding mats, each block with at least 2 nails nailed The thickness of the board should be reserved when reloading the keel. The contact surface between the wood keel and the wall shall be treated with anti-corrosion treatment, and the remaining three surfaces shall be treated with no less than three times of fireproof paint.
4. Lining installation: After the installation of the keel is completed, check the installation of 15mm thick fine wood board as the liner. The lining board shall be nailed firmly. The fixed spacing of the nail shall be controlled around 200mm. The back of the fire retardant paint shall be reserved between the splice plates. About 5mm expansion gap, to ensure that the temperature changes the amount of expansion.
5, install the panel:
The overall wall decoration plate selection color to accompany the grain: Before the panel enters the field, it is selected according to the amount of the same room and adjacent parts, which is the same as the wood grain and the color after the installation.
Cutting board preparation: According to keel line, larger than the distance between the keel board, according to the cut after the big side should be net light (glue plate is strictly prohibited side net), face straight. When the integral wall decoration board is facing to the docking, it must be considered that the joint is located at the cross strut, and the back of the board should be used as a drag force trough to prevent the board from being distorted and deformed. Generally, the distance between the drag grooves is 100 mm, the groove width is 10 mm, and the groove depth is 6-8 mm.
Integral wall decoration panel installation: Before the panel installation, check the keel position, flatness, nail setting, moisture proof layer and other structural requirements. After qualified, install it; after the panel is fitted, try fitting, panel size, joints, The joint structure is completely suitable, the direction of the wood grain, the color appearance is acceptable, can be formally installed; panel joints should be installed when the glue and keel nailing, nail nailing panel specifications should be appropriate, nail length is about panel 2-2.5 times the thickness, the nail spacing is generally 100mm, nail cap should be flat, and use the punch to the nail head along the direction of wood grain into the panel 1-2mm.
Nail sticking face: paste the face should be selected, pattern, color should be similar to the box material, panel. The size and thickness of the face should be the same, and there should be no mistakes.
Above about the construction of the whole wall decoration board is simply introduced here, I hope you pick your favorite overall wall decoration board . If there is anything we do not know where to leave comments on the bottom of the page, we will answer your questions as soon as possible. Thank you for your support of this site. Follow-up articles have been published. Please continue to pay attention.
Decoration materials Interior decoration Wall construction
Our night lights can be used to provide a soft, ambient glow in bedrooms and other living spaces, as well as providing safety lighting in hallways and staircases. By constantly providing new and innovative products with quality and value,we believe that we will be your perfect partner for all your trade development. We will continue delivering new products in range of cabinet lighting, decorative lighting, Motion Sensor Light and table Reading Lamps, Bluetooth speake lamps.
LED Night Light, Night Lamp, Baby Night Lights, Kids Night Lights, Night Light For Bedroom, Sky Starry Projection lamps, light up toys
Ningbo Deamak Star Intelligent Technology Co., Ltd , https://www.deamakstar.com