In one minute, quickly learn to use smart high-speed ball, so you can avoid detours.
The first step: After you get the smart speed dome, remember to take care of the whole process. Because you love your smart speed dome, it will "return" you, that is the lower failure rate, longer life.
The second step: Many people like to use their hands to raise the core of the intelligent high-speed ball during the installation process. Xiaobian recommends that the core of the intelligent high-speed ball be connected to the conductive slip ring interface. It is easy to lift the core wire. It is very easy. Bad interface occurs, the best way is to use your hands to hold the smart high-speed ball.
The third step: During the installation process, the power cable must be led near the intelligent high-speed ball. At the same time, the line of the power adapter of the intelligent high-speed ball should not be extended, and the centralized power supply mode should not be used. Reasons The intelligent high-speed ball centralized power supply, sometimes the voltage to the intelligent high-speed ball will be insufficient, especially in the thunderstorm weather, the resistance resistance increases, the insufficient power supply may cause the motherboard of the intelligent high-speed ball to burn, and thus cannot be controlled.
Step 4: When wiring, remember to distinguish RS485 protocol communication line and power line. If RS485 is connected to the power supply, the intelligent high-speed ball may be burned on the spot, so do the relevant identification, to facilitate their own convenient future maintenance.
Step 5: When installing, the 220V power line must be led to the dome. Do not extend the line of the power adapter equipped with the dome. It is even more impossible to use centralized power supply. Extending the power line or centralized power supply, the voltage to the dome will be insufficient, especially in the rainy days, the line resistance will increase, resulting in insufficient power supply to the dome, and the capacitance of the main control board of the dome will continue to discharge, which may cause the dome board to burn out. , there is no control.
Step 6: The use of smart speed domes in indoor environments is completely different from that in outdoor environments. When installing outdoors, strict waterproofing must be performed. Usually, if there is no professional construction, it is not recommended to lift it outdoors. If you think so, it doesn't matter. I hit glass glue and it's sealed. The Xiao Bian may not agree with it. The gap between glass glue and the intelligent high-speed dome of finance seems to be sealed. However, when you look closely, there is still a small gap, and water is very likely to seep into the dome. The impact of high-speed ball is very large.
Step 7: Test the smart speed dome. It is important to choose the right power source. Why? If the power is too high, the intelligent high-speed ball will be burned. If the power is too low to reach the rated power of the intelligent high-speed ball, the capacitance of the main control board of the intelligent high-speed ball will continue to discharge. This means that the components of the intelligent high-speed ball are The damage will shorten the life of the intelligent high-speed ball.
Step 8: Usually the above steps are successfully completed. The installation steps of the entire intelligent high-speed ball will be almost the same. Now all you have to do is to recheck whether the entire process is correct. In one minute, teach you how to use the Naruto method for smart speed domes. Did you learn?
The first step: After you get the smart speed dome, remember to take care of the whole process. Because you love your smart speed dome, it will "return" you, that is the lower failure rate, longer life.
The second step: Many people like to use their hands to raise the core of the intelligent high-speed ball during the installation process. Xiaobian recommends that the core of the intelligent high-speed ball be connected to the conductive slip ring interface. It is easy to lift the core wire. It is very easy. Bad interface occurs, the best way is to use your hands to hold the smart high-speed ball.
The third step: During the installation process, the power cable must be led near the intelligent high-speed ball. At the same time, the line of the power adapter of the intelligent high-speed ball should not be extended, and the centralized power supply mode should not be used. Reasons The intelligent high-speed ball centralized power supply, sometimes the voltage to the intelligent high-speed ball will be insufficient, especially in the thunderstorm weather, the resistance resistance increases, the insufficient power supply may cause the motherboard of the intelligent high-speed ball to burn, and thus cannot be controlled.
Step 4: When wiring, remember to distinguish RS485 protocol communication line and power line. If RS485 is connected to the power supply, the intelligent high-speed ball may be burned on the spot, so do the relevant identification, to facilitate their own convenient future maintenance.
Step 5: When installing, the 220V power line must be led to the dome. Do not extend the line of the power adapter equipped with the dome. It is even more impossible to use centralized power supply. Extending the power line or centralized power supply, the voltage to the dome will be insufficient, especially in the rainy days, the line resistance will increase, resulting in insufficient power supply to the dome, and the capacitance of the main control board of the dome will continue to discharge, which may cause the dome board to burn out. , there is no control.
Step 6: The use of smart speed domes in indoor environments is completely different from that in outdoor environments. When installing outdoors, strict waterproofing must be performed. Usually, if there is no professional construction, it is not recommended to lift it outdoors. If you think so, it doesn't matter. I hit glass glue and it's sealed. The Xiao Bian may not agree with it. The gap between glass glue and the intelligent high-speed dome of finance seems to be sealed. However, when you look closely, there is still a small gap, and water is very likely to seep into the dome. The impact of high-speed ball is very large.
Step 7: Test the smart speed dome. It is important to choose the right power source. Why? If the power is too high, the intelligent high-speed ball will be burned. If the power is too low to reach the rated power of the intelligent high-speed ball, the capacitance of the main control board of the intelligent high-speed ball will continue to discharge. This means that the components of the intelligent high-speed ball are The damage will shorten the life of the intelligent high-speed ball.
Step 8: Usually the above steps are successfully completed. The installation steps of the entire intelligent high-speed ball will be almost the same. Now all you have to do is to recheck whether the entire process is correct. In one minute, teach you how to use the Naruto method for smart speed domes. Did you learn?
Brass Bathtub Faucet,Brass Tub Faucet,Brass Roman Tub Faucet,Brass Freestanding Tub Faucet
Heshan Janno Kitchen and Bath Technology Co.,Ltd , https://www.janno-ks.com