With the consideration of manpower cost, the combination of manual management and equipment management will be gradually replaced by self-service guest terminals, which will truly realize unmanned and efficient management. The self-service visitor terminal can provide self-service to the visiting person. The visiting person selects the company needing to visit according to the prompt of the touch screen, and enters the personal information of the visitor according to the prompt. The system calls the reception desk of the visited company according to a pre-configured method to conduct a voice call or an IP video call. After the visiting company confirms the identity of the visitor and inputs a confirmation instruction, the self-service visitor terminal spits out the visitor card to complete the visitor registration process. .
In addition, with the improvement of visual aesthetics, people will have higher requirements in the appearance of channel gate equipment. In the increasingly fierce competitive environment of entry and exit control systems, it is believed that more aesthetically-pleasing, powerful, and technologically advanced access products will be launched into the market, giving users a more brand-new experience.
Wing gate <br> <br> a method of mounting, gate wing determination scheme
In the communication with the customer to determine the program, the site width, length, how many machines can be clearly defined, is the choice of vertical wing gate, or bridge wing gate, vertical wing gate size: 420x330x980 (mm), bridge wings Gate size: 1200x280x1000(mm),, wing gate rod to chassis size 510mm, ie, vertical wing gate area: 420x(330+510), bridge wing area 1200x(280+510), determined When selecting the type, fully consider the gap between the gate and the brake lever, the area occupied by each wing gate, the placement position, and how to route the cable (whether it is going through the open line or the dark line). The plan is set, the target is set, and the wing gate is waiting. on site.
Second, fixed position routing
According to the previously determined plan, the specific size of the wing gate should be clearly defined, and the pre-embedded pipe should be completed. The gap between the gate and the gate should be 50-100mm. The upper cover can be opened to prevent adjustment of the machine and maintenance. Leave gaps between the gates and gates to embed 2 plastic pipes with 6 points to 8 points. One hose takes the power line (strong power), and the other hose takes the signal line (weak current). The signal line takes a rubber hose at the same time, which will affect the communication effect. The buried pipe should be exposed to the ground with a height of 30-40mm. The vertical wing gate should be at the bottom of the machine and the bridge wing should be good on both sides. (Because the bridge bottom of the bridge wing is closed).
Third, fixed adjustment
The fixed bottom is fixed with a 4-M10x100 expansion screw, which cannot be swayed. The whole machine is horizontal and the overall appearance is consistent. It is better to use a thin line to pull a straight line before and after fixing, and the vertical and horizontal directions are consistent. The wing gate and the wing gate are connected in series, one by one. Adjustment, straight lines can be used normally.
In addition, with the improvement of visual aesthetics, people will have higher requirements in the appearance of channel gate equipment. In the increasingly fierce competitive environment of entry and exit control systems, it is believed that more aesthetically-pleasing, powerful, and technologically advanced access products will be launched into the market, giving users a more brand-new experience.
Wing gate <br> <br> a method of mounting, gate wing determination scheme
In the communication with the customer to determine the program, the site width, length, how many machines can be clearly defined, is the choice of vertical wing gate, or bridge wing gate, vertical wing gate size: 420x330x980 (mm), bridge wings Gate size: 1200x280x1000(mm),, wing gate rod to chassis size 510mm, ie, vertical wing gate area: 420x(330+510), bridge wing area 1200x(280+510), determined When selecting the type, fully consider the gap between the gate and the brake lever, the area occupied by each wing gate, the placement position, and how to route the cable (whether it is going through the open line or the dark line). The plan is set, the target is set, and the wing gate is waiting. on site.
Second, fixed position routing
According to the previously determined plan, the specific size of the wing gate should be clearly defined, and the pre-embedded pipe should be completed. The gap between the gate and the gate should be 50-100mm. The upper cover can be opened to prevent adjustment of the machine and maintenance. Leave gaps between the gates and gates to embed 2 plastic pipes with 6 points to 8 points. One hose takes the power line (strong power), and the other hose takes the signal line (weak current). The signal line takes a rubber hose at the same time, which will affect the communication effect. The buried pipe should be exposed to the ground with a height of 30-40mm. The vertical wing gate should be at the bottom of the machine and the bridge wing should be good on both sides. (Because the bridge bottom of the bridge wing is closed).
Third, fixed adjustment
The fixed bottom is fixed with a 4-M10x100 expansion screw, which cannot be swayed. The whole machine is horizontal and the overall appearance is consistent. It is better to use a thin line to pull a straight line before and after fixing, and the vertical and horizontal directions are consistent. The wing gate and the wing gate are connected in series, one by one. Adjustment, straight lines can be used normally.
ZHITONG PIPE VALVE TECHNOLOGY CO.,LTD , https://www.ztpipevalve.com