Bosch warm
The advantages of warmth:
1, the heat from the bottom up, in line with the physical needs of the body's head and feet warm, comfortable body.
2, no wind, dust, no noise, anti-mildew anti-mite sterilization.
3, implicit installation, does not occupy space, increase the use of area.
4. High-efficiency insulation layer with high thermal efficiency. After reaching a high temperature, it can maintain the comfort of the room for 8-10 hours, saving 15%-20% compared to other methods such as air conditioning.
5, floor heating generally required heating temperature is between 50-60 degrees, low temperature operation is good for the life of heating pipes and furniture.
The basic conditions for refitting floor heating:
According to heating-related experts, if you want to do warmth at home, you need to add no less than 2 cm thick insulation on the floor, then lay a pipe about 3 cm high, and then leveling and then floor or floor tiles. This will be 7 to 8 cm higher than the ordinary ground practice; it may reduce the net height of the room and affect the opening of the entrance door to the floor heating; if the original security door cannot be transformed and upgraded, it can only accept the floor heating. After the ground is higher than the original, the entrance can be set to become a step, or it can be set into a small space for putting the shoe rack on the door.
Need to pay attention to the problem of modified floor heating:
1, general independent heating floor heating users to choose more, the temperature can be adjusted at any time; if it is centralized heating, want to change to floor heating must be cautious, because the original central heating system is designed and constructed by professionals, there are It is possible that all buildings in the entire area share a common heating system. Before they are used, a comprehensive water pressure test is performed. The temperature of the heating system in winter is also used. If the temperature is too high, you need to consider using a mixing system to facilitate adjustment and reduction. The warm water supply temperature, such as the change from centralized heating to floor heating, requires the re-laying of pipelines. Because there may not be the original entire construction drawings and it is not very professional, it is difficult to ensure that the water pipes will not be connected. Once the water leaks, the consequences will be disastrous. It really needs to be changed. It must be conducted under the guidance of property personnel.
2. For users with independent heating, due to the characteristics of the floor heating system itself, the heating is relatively slow. It usually takes a long time to reach the ideal heating temperature, sometimes even more than 24 hours, so for those occasional back For those who live, if this type of heating is used, it should not be expected to achieve a rapid heating effect; for example, in a room where an independent heating system is installed, during the many days of heating in winter, we urgently need to immediately increase the indoor temperature. If floor heating is not possible at all, it will only take one or two hours for heating radiators to warm up; therefore, in order to ensure a warm environment, we have to turn on the system all day; When installing heating methods, choose to install according to your own situation.
Notes Natural Flooring Del Floor Heating Space Room Furniture Floor Tiles Panel Furniture
Overshot go into the heart of the drill pipe, the slider move up, make the tube socket head can be inserted into the center, when on the slider move up tight, using friction lift drill, remove loose again after the slider, by means of the connection string to slide along the block should tighten, set aside the center pipe, but in front of the salvage must first determine the bit in the bottom of the hole position, can be in a thin plate with bolts tight end of drill pipe, Drop the drill pipe to the bottom of the hole and press it on the drill bit. After waiting for a moment, it is proposed that the relative position of the drill bit at the bottom of the hole and the center of the rotary plate of the drill can be determined by observing the indentation left by the center pipe of the drill bit on the board, and then move the drill or rotary plate so that the center of the rotary plate is directly in front of the center pipe of the injured head, so as to ensure that the fishing device can be inserted into the center pipe accurately.
Overshot Assembly,Fishing Tools,Overshot Assembly For Sale,Overshot Fishing Assembly
WUXI XINZUAN GEOLOGICAL EQUIPMENT CO.,LTD. , https://www.wxsmrxz.com